Mackie SRM350 V2 Owner's Manual download pdf (Page 9)

4. CONTOUR

Pushinginthisswitchengagesalterthatprovides3dB

of boost to the low and high frequencies (below 100 Hz

and above 12 kHz). This provides a punchy, crisp sound

for most live music applications. You can experiment with

this switch by leaving it out for a while, then pushing it in

to determine which way sounds best for your application.

It is especially useful when listening at lower volumes, as

it highlights the bass like a Loudness switch, in addition to

boosting the highs.

5. LEVEL

This is used to adjust the signal level going into the

built-in

power ampliﬁers, from off up to 45

dBofgain.Since

the SRM350v2 incorporates Mackie’s world-class low-noise

mic preamp technology, you can connect either a line-level

or a microphone-level signal to the input, and use this

control to adjust the level correctly.

There is no phantom power provided for a

microphone, so you should use a dynamic

mic, or use a condenser type if it has its own

battery power.

Follow the Quick Start guide on page 6 for setting the

LEVEL control. For most applications, it will be in the

NORMAL position (12 o’clock). If you have a particularly

high line-level signal connected to the SRM350v2, you may

need to turn the control down to the 9 o’clock position.

If you have a low line-level or mic-level signal connected,

you may need to turn the LEVEL control up to the

3 o’clock position.

6. MIC/LINE Switch

Leave this switch out when connecting a line-level signal

to the INPUT connector (from a mixer, graphic EQ, or other

line-level signal source).

Push this switch in when connecting a microphone

to the INPUT connector. Since a microphone produces a

much smaller signal than a line-level signal, this provides

anadditional40dBofgaintoboostthemicrophonesignal

to a line level.

7. SIGNAL Indicator

This LED illuminates whenever there is a signal present

at the INPUT connector on the rear panel. It senses the

signal just after the LEVEL control, so if the LEVEL control

is turned down, the SIGNAL indicator won’t light.

8. LIMIT Indicator

When the signal levels at the ampliﬁer outputs approach

clipping, a soft limiting circuit is activated that reduces

the input signal. The LIMIT LED lights whenever the limit

circuit is active.

It’s okay for the LIMIT indicator to blink occasionally,

but if it blinks frequently or continuously, either turn down

the signal level at the mixer or other signal source, or turn

down the SRM350v2’s LEVEL control.

Wear hearing protection if you are close to

the SRM350v2 playing at high levels.

9. INPUT Connector

This is a combination female XLR-type and 1/4" TRS

connector that accepts a balanced or unbalanced mic- or

line-level signal.

10. THRU Connector

This is a male XLR-type connector that can be used to

daisy-chain the input signal to another speaker.

The signal at this point is after the MIC/LINE switch but

before the LEVEL control. If you have a microphone

connected to the ﬁrst SRM350v2 and you have the

MIC/LINE switch pushed in, the signal at the THRU jack

isboosted40dBtoaline-level,soleavetheMIC/LINE

switch out on the next SRM350v2.

12k/AIR100Hz

CONTOUR

(+3dB)

POWER

LIMIT

SIGNAL

LINE

MIC

LEVEL

+45

+5dB

NORMAL

PARALLEL

INPUT

THRU

ACTIVE SOUND REINFORCEMENT SYSTEM

MANUFACTURING DATE

SERIAL NUMBER

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR

MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

AVIS:

RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Comments to this Manuals

No comments

Mackie SRM350 V2 Owner's Manual Page 9

Comments to this Manuals

Related products and manuals for Supplementary music equipment Mackie SRM350 V2