Mackie DLM12 Owner's Manual download pdf (Page 11)

Owner’s Manual

DLM12S Subwoofer: Rear Panel Features continued...

9. OLED Display

TheOLEDDisplayisoneofthemostvitalfeatures

oftheDLM12Ssubwoofer.Itdisplayssubwoofer

informationincluding(butnotlimitedto)volume,

selectedcrossover,delaysettingsandotherparameters.

WhenaDLM12Ssubwooferispoweredup,thelast

stateitwasinwillloadupandtheOLEDDisplaywill

presentthevolumescreenandsettings.

DLM12SsubwooferswilldisplayarunningRunning

Manscreensaverifparametershaven’tbeenchangedin

awhile.SimplytouchoneoftheDLPbuttonsto“wake

up”theOLEDDisplay.

10. VOL Button

Volume[VOL]adjuststheoverallsignallevelatthe

inputstothebuilt-inampliers.PresstheVOLbutton

toaccessandupdatethesubwoofer’svolumeand

changethevolumebypressingthe+or–button[16]

repeatedlyuntilyouhavereachedthedesiredvolume.

Thevolumerangesfromoff(–

dB)to+10dB.

11. XVR Button

TheDLM12Scrossover[XVR]allowsyoutochoose

fromalistofpresetcrossoverfrequenciesforMackie

loudspeakers,asnotedbelow.Thisoptimizesthe

subwooferandloudspeakersconnectedtothe

DLM12Shighpassoutputs.IfnotusingDLMorSRM

loudspeakers,avariablemodeallowsyoutoselect

thebestcrossoverfrequencysuitedforyourPAsystem

from60Hzto120Hz.

Frequenciesbelowtheselectedcrossoverfrequency

aresenttothesubwooferwhilefrequenciesabovethe

selectedcrossoverfrequencyaresenttothehighpass

outputs[6].Thecrossoverfrequencyshouldbeset

tothelowestfrequencyresponseratingofthemain

loudspeakers.PresstheXVRbuttonrepeatedlyuntil

thedesiredcrossoversettingishighlighted.

• DLM8:110Hz

• DLM12:90Hz

• SRM350:100Hz

• SRM450:95Hz

• Variable:60Hz–120Hz

Thelastonelisted–variable–maybesettotaste.

Simplypressthe+or–button[16]repeatedlyuntil

youhaveachievedthecrossoverpointyoudesire. 

Itrangesfrom60Hzto120Hz.

12. Front LED On / Limit / Off

PressingtheVOL[10]andXVR[11]buttons 

simultaneouslygivesyoutheoptiontoturnthefront

LEDon,offorlimit.Pressthe+or–button[16]to

makeachoice,followedbyanyotherbuttontoexitthe

screen.ChoosinglimitmeanstheLEDisonfull-time.

However,itwillickerwhenthelimiterisactive 

[3dBofattenuation,averaged].

13. DLY Button

Delay“delays”theaudiosignalforasetperiodof

time.WiththeDLM12Ssubwoofer,it’susedforaligning

delaystacks,balconylls,etc,notasaneffect.

PresstheDLYbuttontoaccessandupdatethe

subwoofer’sdelay.Changethedelaybypressing

the+or–button[16]repeatedlyuntilyouhave

reachedthedesireddelay.Delaytimesrangefrom

0ms[0.0feet/0.0meters]to300ms[337.8feet/

102.9meters].

14. MEM Button

SettingsforDLMsubwoofersmaybesavedtomemory

andrecalledatalatertimebyutilizingthememory

[MEM]button.

Pressthisbuttonrepeatedlyuntilthepresetspot

youwanttosavesettingsto(orrecallsettingsfrom)is

highlighted.Therearethreeuserpresetsandafourth

torecallthefactorydefaultsettings.

Oncethepresetyouwanttosaveto(orrecallfrom)

ishighlighted,pressthe“+”button[16]tosavethe

currentsettingsorpressthe“–”buttontorecalla

presetthatwaspreviouslysaved.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 21 22

Comments to this Manuals

No comments

Mackie DLM12 Owner's Manual Page 11

Comments to this Manuals

Related products and manuals for Soundbar speakers Mackie DLM12